Page 6 - Link International Battery 2022 Catalogue
P. 6
BATTERIES – ROADSTAR BATTERIES
ROADSTAR BATTERIES COMMISSIONING A NEW ROADSTAR BATTERY
07 – BATTERIES
12 Volt STD, Heavy Duty And Cx Heavy Duty Series:
FOR MOTORCYCLES, SCOOTERS, ATVS, 1. Remove the sealing cap / tape just prior to filling, fill with the correct amount
of electrolyte.
PWCS & RIDE-ONS
• Roadstar batteries have been developed and produced to the highest 2. Attach the open-ended exhaust vent hose to the battery if required.
international standards 3. Allow the battery to stand for approx 30 minutes and then check the
• All materials used are certified and manufactured to ISO 9001 standard terminal voltage.
• The Roadstar range of available batteries is one of the World’s most complete
product lines 4. If the terminal voltage is greater than 12.8V, proceed to step 5. If less than 12.8V,
then charging is required as per the enclosed instruction sheets. OR alternatively,
BATTERY TYPES AVAILABLE: charge the battery with a low output ‘Intelligent’ charger (i.e. Noco Genius) and
remove when fully charged is indicated.
• Standard and Heavy Duty batteries – Flood cell / dry charged
• Supplied with acid pack/s to fill the battery 5. After charging, check the electrolyte level and top-up if required. Allow battery to
• This type of battery should be maintained and serviced with distilled water cool prior to fitting to vehicle.
when required 6. Install the battery securely and ensure the terminal lead polarity attachment is
• Refer to “Commissioning a new ROADSTAR Battery” for the procedure when correct. Failure to comply with these instructions may reduce the expected battery
servicing a new battery life and void the warranty.
Heavy Duty CX batteries – Flood cell / dry charged 12 Volt Sealed Factory Activated AGM
• This type of battery is constructed with Lead-Calcium technology which increases
the performance and reduces the maintenance – ideally suited for Harley Davidson. (Absorbed Glass Matting) Series:
Supplied with an acid pack to fill the battery 1. Check the voltage of the battery prior to installing: If voltage is greater than 12.8V,
• This type of battery should be maintained and serviced with distilled water when required proceed to step 3. If voltage is lower than 12.8 V, charging is required
• Refer to “Commissioning a new ROADSTAR Battery” for the procedure when (refer to step 2).
servicing a new battery 2. Charge the battery as per the enclosed instruction sheet OR alternatively, charge
MTF Maintenance Free Battery – A.G.M. the battery with a low output ‘Intelligent’ charger (i.e. Noco Genius) and remove
when fully charged is indicated. Allow battery to cool prior to fitting (30 minutes +).
(Absorbed Glass Mat) dry charged
• This type of battery comes dry charged with model specific acid pack/s. (If two 3. Install the battery securely and ensure the terminal lead attachment / polarity is
acid packs are supplied with the battery, both are required to complete the initial correct. Failure to comply with these instructions may reduce the expected battery
‘wet-up’ procedure) life and void the warranty.
• Once filled, the battery is sealed and no further maintenance is needed, providing 12 Volt MFT AGM (Absorbed Glass Matting) Series:
the charging system is operating correctly. If excessive over charging occurs, top up
with distilled water 1. Remove the sealing tape and start filling the battery with the acid from the
• Refer to “Commissioning a new ROADSTAR Battery” for the procedure when supplied pack/s.
servicing a new battery 2. After all the acid has been added, allow the battery to stand with the acid
pack in place for a minimum of 30 + minutes. This will allow the electrolyte to be
absorbed completely.
3. Battery must be re-sealed with the supplied sealing cap/plugs. Allow the battery to
stand for an additional 30 minutes prior to checking terminal voltage.
4. Check the output voltage. If greater than 12.8V, proceed to step 6. If less than 12.8V,
Charge the battery as per the enclosed instruction sheet. OR alternatively, charge the
battery with a low output ‘Intelligent’ charger (i.e. Noco Genius) and remove when
fully charged is indicated.
5. After charging, allow battery to stand for one hour and check the battery voltage. If
below 12.8 volts, allow battery to cool and re-charge as per step 4.
6. If battery is warm or hot, allow to cool. Install the battery securely and ensure
the terminal lead attachment / polarity is correct. Failure to comply with these
instructions may reduce the expected battery life and void the warranty.
12 Volt GEL SPEC Sealed Factory Activated Series:
1. Check the voltage of the battery prior to installing: If voltage is higher than 12.8 V,
proceed to set 3. If voltage is lower than 12.8 V, charging is required (refer to step 2).
2. Charge the battery as per the enclosed instruction sheet OR alternatively, charge
the battery with a low output ‘Intelligent’ charger (i.e. Noco Genius) and remove when
fully charged is indicated. Allow battery to cool prior to fitting (30 + minutes).
3. Install the battery securely and ensure the terminal lead attachment / polarity is
correct. Failure to comply with these instructions may reduce the expected battery
life and void the warranty.
PAGE 444